To season a new Blackstone griddle, wash the top once with hot soapy water, dry it completely, then heat it on high and wipe on very thin coats of oil, letting each coat smoke until the smoke dies down. Three to five coats usually turn the steel from silver to brown to patchy black, and the first cooks finish the job. Below are the steps in order, how much oil per coat, which oils to choose, the mistakes that leave a sticky top, and what to do when the edges stay bronze or rust shows up later.
What Seasoning Actually Builds
A griddle top is bare rolled steel. When a thin film of oil is heated past its smoke point, it polymerises: the oil molecules link into a hard, slick layer bonded to the metal. That layer does two jobs. It keeps moisture off the steel so it does not rust, and it gives food a surface that releases instead of sticking.
Blackstone’s own griddle care and seasoning guide lists both purposes and stresses that seasoning is ongoing: the more often you cook on and season the griddle, the more non-stick it becomes.
Step by Step: The First Seasoning
- Wash once with soap. The top ships with a protective oil film. Blackstone’s guide says to wash it in hot, soapy water for first-time use, and that this is the only time you should use soap on the griddle. Rinse and dry completely with paper towels.
- Heat it dry. Turn all burners to high for 10 to 15 minutes. The centre will start to darken and may look bronze or blue in patches. That is normal.
- Apply a very thin coat. Pour about a tablespoon of oil onto a 36-inch top (less on smaller models) and spread it with a wad of paper towels held in long tongs. Cover the whole surface, plus the sides and front edge. It should look almost dry, not wet.
- Let it smoke. The oil will smoke heavily, then taper off. Wait until the smoke has nearly stopped, typically 5 to 7 minutes.
- Repeat. Apply the next thin coat and repeat the cycle. Three to five coats are typical for a new top.
- Finish with a light oil. After the last coat has stopped smoking, turn the burners off, wipe on a final film of oil, and let it cool.
Budget 45 minutes to an hour for the whole job, outdoors, away from anything that minds smoke. The guide at The Flat Top King reports a new griddle needing four to five coats on that timescale, with each coat taking roughly 8 to 10 minutes.
How Much Oil Per Coat by Griddle Size
| Griddle top | Oil per coat (starting point) |
|---|---|
| 17 or 22 inch tabletop | About 1 to 2 teaspoons |
| 28 inch | About 2 teaspoons |
| 36 inch | About 1 tablespoon |
These are starting points, not rules. The test is the look of the surface: if you can see pools or streaks, wipe more off. Thick coats never fully harden and leave a tacky, gummy surface that collects grit.
Which Oil Works Best
Blackstone’s guide lists olive, vegetable, canola, coconut and sesame oils, and lard. In practice, many owners prefer neutral oils with a high smoke point for the first coats:
- Good choices: canola, vegetable, grapeseed, avocado oil, solid vegetable shortening, or a commercial griddle conditioner.
- Use with care: olive oil works but some owners report a stickier finish on the first coats.
- Skip for the base layers: butter, which burns rather than bonding.
Is It Done? Signs You Can Start Cooking
- The centre is dark brown to black and has a slight sheen.
- The surface feels smooth and dry when cool, not tacky.
- A drop of water skitters across the hot top rather than sinking in.
Corners and edges often stay bronze after five coats, because those areas run cooler. That is fine. They darken as you cook. Fatty first cooks, such as bacon, smash burgers or fried onions, help season the top while you use it. If you plan to start with burgers, this guide to smash burgers and the beef that suits them pairs well with a freshly seasoned top. Our comparison of griddle vs grill covers which foods suit the flat top best.
Common Seasoning Mistakes
Too much oil
The most common error. Thick coats stay soft and peel. Wipe it back to a sheen before each smoke cycle.
Stopping before the smoke clears
Adding the next coat while the last is still smoking stacks unhardened oil. Wait for the smoke to taper.
Cold water on a hot top
A sudden flood of cold water over the whole hot surface can warp the steel. Let it cool, or use hot water in small amounts when cleaning.
Keeping It Seasoned After Each Cook
Blackstone’s guide recommends scraping the top with a spatula after cooking, wiping it with paper towels, and using hot water to lift stuck food. Table salt can scrub off stubborn bits. Dry it, wipe on a thin film of oil while it is still warm, and cover it.
Grease-cutting dish detergent strips the seasoning, so leave it for the very first wash only. If rust appears, the guide says to remove it with steel wool or fine sandpaper and re-season. Humid and coastal areas need more frequent oiling. The same burn-in logic applies to new smokers, which our article on how to season a new smoker explains.
Frequently Asked Questions
How many coats does a Blackstone need?
Most new tops look ready after three to five thin coats. Count by appearance, not number: stop when the centre is dark and smooth and the surface is no longer tacky. Older or rust-treated tops sometimes need a few more. Every cook after that adds a little more seasoning, so the colour keeps deepening over the first few weeks.
My griddle is sticky after seasoning. What went wrong?
The oil coats were too thick or were not heated long enough to harden. Turn the burners to high and let the surface smoke until it stops, which often firms it up. If it stays gummy, scrape the soft layer off while hot, wipe it clean, and re-season with much thinner coats.
Do I need to re-season after every cook?
Not a full seasoning. A thin wipe of oil on the warm, clean top after each cook is enough to protect it and add to the layer. A full multi-coat seasoning is only needed for a new top, after rust removal, or if the surface has been stripped by detergent or harsh scraping.
Can I season a griddle on a cold day?
Yes, but it takes longer. Cold air and wind cool the steel, so the oil may smoke unevenly and the edges stay pale. Shield the griddle from the wind, give it a longer dry preheat, and allow a few extra minutes per coat. A wind guard or simply turning the unit helps.